Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
This great article which follows on the subject of Installing A Bathtub is indeed entertaining. Try it and draw your own final thoughts.
Mounting a bathtub isn't precisely rocket science, however it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably tough job. If the old tub is readily available, the project can move immediately; if you need to open up a wall surface to remove the old bathtub as well as position the new bath tub, the job is much harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and also set in the brand-new one. Make sure you have qualified yourself for the task and fit attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is better to consider utilizing one before you start. Possibilities are you might require an expert plumber to make tube links.
This short article will certainly help you mount a new bath tub in your shower room if you have actually already bought a brand-new bathtub and also don't require to change the plan of your previous supply of water pipelines.
Your tools as well as product checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather bothersome due to the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The previous type must be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the called for placement. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bathtub till the spirit level reads degree.
To install taps, fit the bottom of the outermost versatile faucet connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and inspect all joints as well as new pipework for leaks and also tighten them if essential. Load the bathtub and also examine the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub should wait up until the bathtub has been used at least when as this will certainly settle it right into its last position.
Preparing for the Installation
First of all, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealer can crack rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader on Tools You Need to Install a New Bathtub , I assumed sharing that piece was a good idea. Sharing is nice. Helping others is fun. Thanks a bunch for your time. Come back soon.
Pro service? Ring! Report this page